Recent content by icemanjc1

Looking for some feedback about these 100hp 6.7 injectors from fleece, how do you like them? Are they different in appearance injector body wise, dual plane or single plane nozzle...

Selling my nozzles from my 08', ran these for less that 400 miles. Truck ran great with these, no problems, just needing to scrape up some money. $650 shipped, paypal preferred.

I've had this issue with 2 different brand new borgwarner s400's. I put about 5k miles on this compound setup, then i pull the pressure pipe from the primary and sure enough, oil residue. Same as the s471 I ran for a couple years. I'm using a #4 (1/4")hydaulic line for oil feed and the stock...

For sale is a Destroked adapter plate for a CR Cummins to 4r100 v10 transmission. Comes with starter mounting bolts. $625 shipped.

I have an excellent set 70% injectors for sale, balanced to less than 2% and only have 6,000 miles on them. $2800 shipped for the set, no cores needed. Trades possible. Does include balance sheet.

For sale is a billet comp wheel for the s471 BW turbo. Purchased this wheel from MIC turbo. Mounted to the turbo once, never ran because I decided to run a bigger turbo. $200 shipped.

For sale Arson 3 CP3 upgrade kit from Motorsport diesel. Less than 500 miles, been on the truck about a month. This is for early style CP3 with 19mm hex head cascade valve. $350 shipped, paypal +3% to cover fee please. Arson III 6.7 CP3 upgrade kit

Selling my Garrett GTX4202R. Has approximately 12k miles on it, great condition, does have some scratches on the comp cover, same shaft play when I bought it new (from Himni Racing). Comes with your choice of a T6 1.10 housing, T6 1.28 gated housing, or a T4 1.01 housing. $1900 plus shipping...

I'm having a hard time figuring what my compression ratio is at. Could use some help. What I have is a .020 over 6.7, stock pistons, stock MLS headgasket, -0.010 from the deck, -0.009 from the head, .025~ protrusion, stock valves and seats. I can't find a good CR calculator, plus the fact I...

A set of Flux 4 nozzles for sale for a 03-04 CR. 3000 miles on them, they run clean for a 5 hole SAC type nozzle. $700 shipped.

Presently I'm running a GT3788R over GTX4202R on my 06 5.9. The secondary is a 63/64/.99 T3 and the primary is a 76/75/1.15. My boost numbers on the primary are almost exactly half of total boost in almost every case. By the numbers (PR), my primary is doing most of the work. I wonder if...

Selling my P7100, has around 6000 miles on the rebuild. It is a 215hp 887 pump that I sent to Seth at DPE, it has new flat top 12mm barrels and plungers, 181 DV's, 520cc at full foward, #100 plate, 3k City Diesel Governor springs, pinned at 19*. $1500 plus shipping, no core needed, location...

I have a new JGS 400R wastegate for sale. Comes with SS bends and flanges. Full description here JGS Precision Turbo Wastegates and Bypass Valves. $230 shipped to the lower 48. Also a 60mm blow off valve, new as well. JGS Precision Turbo Wastegates and Bypass Valves. Comes with an...

Up for sale is a Bully Dog PMT #40300 with Crazy Larry. Comes with pyrometer probe. $400 80% Exergy honed Bosch nozzles. These were my old (old style as well, not cup & puck) stock nozzles, had 70k miles on them before I had them honed. About 25k miles after that. $300 Stock exhaust...

Hey Don, I have a set of old style Flux 2's nozzles here, I've put about 40k miles on them. My question is can I send them off to you, have them cleaned and inspected/tested? Also since these are the old style, would it be possible to have the pintles cut so they would work on the new style...