Recent content by whitneyj

Was rebuilt before I bought it, it’s been sand blasted and painted with a 2000+° silicon paint, normal radial play, no axial play, I only had it on the truck a few hundred miles, it’s just too large for me. I have a box and foam from another turbo I can ship it in so it’ll be very well packaged...

Just pulled this off my truck when I did my 2nd gen swap. It was on for roughly 1 year, less than 10K miles. $200 obo shipped Located in Oshkosh, WI (9one0)four78-8fourzero8 EVO8004 - Injen EVOLUTION Cold Air Intake System | Injen Technology

Edge no longer makes the CTS2 Insight Pro that accepts HP Tunes and no longer modifies the CTS2 to the Pro so I'm on the lookout for one. Located in Oshkosh, WI (9one0)four78-eight4zero8

Truck is a 2004 5.9, 50% over, Airdog 4G, 2nd gen manifold ported, Edge Juice w/ Attitude (unlocked 6th tune) and the turbo is a 66/71/13ss with the turbine housing port matched to the manifold. It doesn't start to light until 2000rpm and is slow to build to ~42psi before I run out of rpm's. I...

Looking for a 22-26cm housing. Located in Oshkosh, WI (9onezero)47eight-84zero8

Tranny is from a 1998.5 Dodge Cummins and comes complete with clutch, crossmember, pedals, hydraulics, driveshaft, ect. Essentially everything needed to swap it into anything. Odometer says 334K miles, truck was a delivery truck for a butcher so it should be primarily highway miles. Shifts...

Parting out a 1998.5 Cummins, VP44 powered 24 with all accessories to include starter, harness, turbo, computer, ect-whatever you want. Has 334k on the odometer, no blow-by, looks to have had headwork done (assuming head gasket), new VP44 around 200K miles ago, no leaks, bone stock, and never...

I'm looking for a D61 center section with 3.07 gears or a complete D71 with 3.07 gears. I'm in Oshkosh, WI Text me at (nine one 0) 4seven8-84zero8 or PM me since I'm on here often enough.

It's cleaned up now, this was directly after building it and a terrible picture to show.

Picked it up off of here for my new motor (P-pumped 24V) and ended up selling the truck before putting it on. I paid $300 plus shipping for it and that's what I'd like out of it. I also have a modified front cover I built to allow access to the pump gear without taking everything apart. I'm...

This is it in the original packaging, never been mounted or welded to.

sale pending on the FASS. I only have pictures of the mechanical clutch, not the electrical one. Half of the electrical one was scrapped, the other half is still bolted to the fan. Is that what you're looking for is the electrical one? You can sort of see the shaft for the electrical...

2002 Cummin's 24V VP44 cylinder head-has valves, springs, retainers and the typcial small VP44 cracks between the injectors and valves. Machine shop pressure tested it and said it's fine. But because it's not flawless I can't guarantee anything-$50 2 2" aluminum spacers-8x6.5"-they have 3...

I'm looking at building a front D80 and need a housing for the center section. Just seeing what you guys have out there that's lost a spindle, spun a tube, or destroyed something other than the housing. Last one I bought I paid $100 for the housing with bearing caps and a few inches of tube on...

Probably a long shot but I figured I'd toss it up here as well. I have a 02 Superduty HPD60 complete minus the lockouts that I'm looking to trade for a SRW Chevy front D60, preferably with 4.10's. When I picked the axle up I was told it had 120K on it. Nothing seems worn out or damaged and...