Search results

Im trying to locate a wiring harness for a 2008 dodge ram auto push button 4 wheel drive. Also the fuel lines and tail lights wiring.

Where do the timing marks line up on a 2002 dodge , ho motor, and ho pump. Some people say long ass the crank and cam line up with 0 on crank and 00 on cam then 0 on cam with 00 on pump gear . Then others say don't matter pm vp44 pump alignment on the 0 s . The only one that matters is the o...

I don't get any throttle response till my throttle is a 1/4 way down. Reset apps. Still no change . Put a bd throttle booster. Still no change on peddle. I have 18 psi on fuel pressure drops down to 15 psi wot.

On my injector nozzle it has ph820 -3 hi flow stamped on the nozzle. What does that mean?

Put a gas rag in air breather it trys to start but doesn't even run. Broke 4 injectors loose they are pumping fuel. Closed them. Still won't start

Do I need that oil cooler on passenger side of motor ? The previous owner removed it . This is the first time I noticed that cummins had a oil cooler on the passenger side of the block. So I'm wondering the pros and cons of running one and not running one

What company pays the highest for vp44 core

2008 f250 turbo 6.4 diesel twin turbo aftermarket trans, oversized injectors bored, nos and studded after market fuel pump stabilizer race package tuned with hns. Has hole in the blockWill not part out. Do not have title

My 3rd cylinder warm up has stopped coming on. The truck will idle up but right when it should kick over to the 3rd cylinder it just stays at high idle. O tap the throttle it starts idling. What could be keeping it from doing the 3rd cylinder warm up? It was like 35 degrees also.

Where's the best place to get the highest price for vp 44 cores

If the truck sits over 30 min. I have to bump the key three times or more times. Letting the lift pump cycle. Then the truck will start. I just changed my airdog fuel filters and installed a vp44. This has been going on for over a month now. Now if I jumper my airdog let it run for a while...

I bought a turbone hx40 off a guy on fb. I can't find any info about it.

Who's the highest for vp44 cores

Can vp44 injectors go bad? I sent a set in and the shop said they won’t build pressure to pop? What can be done to fix this?

What's the difference of a short shifter and speed shifter for a 2002 dodge 6 speed?

I installed a vp44 from therobred. It's the 245 hp one. It doesn't respond hard or smoke any were near my old pump. Even though it finally went bad. I just put on the smarty it smoke a bit. I stack it with my tst comp and smarty on 8. It's like I have nothing hooked up. My light is kicking on...

When I do the turn the key trick I get only the 1693. Now if I check it with my smarty i have 1690 and 1693. I reset the truck by pulling batterys with the key on. The light comes back on with in a minute. I also have dead pedal. There is no white smoke also.. Any ideas

My gear is messed on my vp 44. . Needing to replace it. So do all vp44 gears the same or do I need to order a gear labeling specific?

The truck was running fine and just died. The truck will turn over. Just won't run. Put a gas rag in air filter it trys to run. The only codes I have on is p0203 and p1693. The lift pump is pumping fuel. I have fuel coming out on the injectors that I left loose. Just can figure out why...

i swapped out my ho pump to a so pump because it was dead pedaling. i also installed some 150 hp injectors. does that so pump have enough to feed those injectors? i have a tst comp and smarty stacked.