Search results

So, as the title states. I have it on the analog gauges and everything was fine and then I lost my turbo boost reading and my engine coolant temp. My egt still reads fine. I did notice that my engine light came on and there were no codes and I checked my obd II and it was a little loose. I...

Anyone done this? Searching has not resulted well.

What are the specs on a 62? The one I have, which came from II has 62/70 engraved on the data plate. Thank you

2nd gen 1/2 ton short wide. Planning a 6.7 Cummins Auto...truck will be a DD, but take it to the track, throw on some meats. Now to the hard part, what's best way to keep power to the ground w/ out a 4 link? A Chrysler 9.25(how much will these take) or should a Dana 80 replace it? What would be...

Asking $600 shipped or trade for a s475/83 1.10 t-6 Turbo is currently on the truck and in great shape, which is driven mainly as a DD. I have some wiggle room on price and located in Jacksonville, Ar. Thanks, Jody

Anyone have good info on these tractors.

S475/96-1.32 T-6 $775 shipped/or a reasonable offer, I realize I may be a little high For sale or trade for 475/83-1.10 T-6 Turbo is still very good and is currently on truck, Thanks, :thankyou2: Jody

Eric, I have a 97 Dodge, 12v Cummins. I wanted to go w/ an Adjustable Timing gear. I also have a Fluid Damper Harmonic balancer. Which Timing cover can I use? Thank you, Jody

I already have compounds, signature truck. Looking to go 5x.016 or ?.018? even. Looking to go ball bearing for both. Truck is a dd and then I pulled my boat to the lake as much as I can. 21.5' Mariah Cuddy Cabin, about 6000lbs, not exactly sure. I'm sure .018's are OVERKILL, but when someone...

So, I've started looking at the newer Fords and I hear a lot about the injection pump/injectors being problematic and also Ford blames it on bad fuel...I'm a Cummins guy, but looking to expand my horizons... Thanks Jody

Jamie, I have a set of your injectors. They are stamped 260 Bar. Truck didn't seem to be running as good so I pulled them last night and 1 & 3 were wet w/ fuel, the others were dry w/ slight carbon build up as expected. Could the injectors have lost their pop pressure causing them to leak...

I pulled my injectors this evening to check them as well as clean them. Number 1 & 3, the tips were wet. The others all looked to have a little carbon built up and were dry. Why would 1 & 3 be wet? Am I only running on 4 cylinders, I would think it would be running very rough if that was the...

Anyone running an he451 on a 6.7 Cummins? I believe it is a vgt as well as the stock 351 and are used for some of the Mack trucks, Dump and Cement...

Sir, How will the Switch Blade work on a 12v? For say the one in my sig? Thanks, Jody

I read in Diesel Tech Magazine, that Pat Liskey used y'all to rebuild a p-pump and the article claimed 900cc's and using DDP 90HP injectors. Was the pumpe bumped to a 13mm and were stock injector lines used? Thanks, Jody

Anyone out there running a 475/83 or 87 1.10 a/r? I'm currently running a 475/96 1.32 a/r. Looking for input on a better and responsive DD. I realize I could step up to 5x.016's, which is in the works. I also know the smaller turbine wheel and housing is more expensive, but not worried about...

My question is, which are better:nail:...F1 or Exergy? I know most in the 12v world prefer Smokem's or Contagious. Just looking for some guidence...reliability, quality, I reckon is the main concern and the other being power, of course. The set up is an 06, Box 366, 100hp/50% over inj., stroked...

Anyone have experience with the Indy or Fatt technology 12v aluminum head?

What are the flow ratings with the aluminum 12v head?

Anyone benefitting from these.... power or just preventative wear from higher compression springs, rpm's, etc... I found this quote on Torkteknology... Reducing valve train mass (weight) has many benefits for a performance Cummins diesel engine. Less weight in the valve train allows the...