Recent content by mopo824

Used ATS stand-alone select shift valve body with harness/pcs. Gone through and cleaned by ATS. Part# 3039502000. Harness Part# 601-950-2104. Comes with everything I have for it which should be all you need to install it. $1500 Used Suncoast stand-alone valvebody with harness/pcs. This is the...

Garage parts sale! Everything is located in Liberty Texas 77575. Prices do not include shipping if that is needed. PM me your email and what you would like pictures of. New 1.5" steel wheel spacers 8x6.5 9/16 x 18 thread (94 - early 4th gen dodge). $150 New 2" steel wheel spacers 8x6.5 14 x...

Want to sell or trade this complete ATS standalone setup. Comes with harness, serial to USB connector, PCS tcm, PCS pressure sensor, ATS valvebody for this setup, and all bolts needed to install the valvebody. Due to the size of the vb you will require a DD pan if I recall correctly. All parts...

Selling these 2 turbos that I was going to use in a twin setup. I have decided to go with a larger setup so I'm letting these go. They have been gone through and since haven't been ran. I have taken them out of the boxes for pictures and that's it. $1900 shipped to your door for the pair...

I have an AirDog 150gph for a 94-98 12 valve that i am looking to part with. it has about 5000 mile on the system and will come with everything that it would come with new. I did have to cut the hose for dual feeding my pump (only cut part of the hose) but i left plenty of room to tie it back...

Needing a price on some arp 625's for a 95 12 valve. Will be needing these ASAP as well as in the next week. Please let me know about a price and if you have some in stock.

So as my build progresses i have started looking into setting up the rear suspension in my truck. it is a 95 scsb 12v that i am looking to get into the 900-1000 hp range. at the moment i have the rear sitting about 1.5-2" lower than factory. I will be removing this and going with another setup...

I have a dana 70 in my 95 scsb 2wd 12v thats in my sig. does anyone know if they make aftermarket axles for it or axle studs? i have looked into it with little to no luck. i dont want to have to swap rears unless i have to or wait until this one eats itself if there is nothing available. mine...

So i picked up a schied 13mm p7100 for my 12v. I am currently making some changes to the truck and i am looking for some information from those who are more knowledgeable than I. I have searched and just cant seem to find an indefinite answer which i know is all apart of test/tune. I am wanting...

so i am looking to see if anyone could haul a truck for me if i can not get a break from work. and if i can possibly rent a trailer before i go out and buy one lol. truck is an 04 dodge 2500 4x4 6" lift with 35" tires on 20" rims. sits right around 7' - 7' 1" or so. it would need to be hauled...

First off I will be in need of a roll cage soon. With that said the guy I was going to originally use near me has closed shop. I need an 8 point cage built for a 1995 scsb Dodge Ram. I am about 45min-1hr east of Houston and im looking for a reputable shop that can perform this work for me...

So after talking with another guy who has a scsb like I do I have made a decision on tire size to run while racing. Probably going to go with the Mickey Thompsons in a 33x10.5x16 with the rim being 16x7 front and 16x10 rear. The problem I am having is deciding on which tire compound to run M5 or...

So I am in the market to put an egate on my truck, which is a 95 12v. I will be swapping out the II62 to a 66/74/14 over the s480. I want to put a gate between the manifold and the s366. Reason behind this is obviously the pressure but its also peace of mind for when i spray if i do. i am...

I have a few items i need to part with right now that i wont be using. Up first is an nv5600 4x4 transmission out of my 04.5. It was rebuilt sometime last year i will have to find the receipt for it. when pulled it had about 1000-1500 miles on it reason for pulling was to go to a built...

Figured I would stop off and say hello to everyone out there