Search results

Was rebuilt before I bought it, it’s been sand blasted and painted with a 2000+° silicon paint, normal radial play, no axial play, I only had it on the truck a few hundred miles, it’s just too large for me. I have a box and foam from another turbo I can ship it in so it’ll be very well packaged...

Just pulled this off my truck when I did my 2nd gen swap. It was on for roughly 1 year, less than 10K miles. $200 obo shipped Located in Oshkosh, WI (9one0)four78-8fourzero8 EVO8004 - Injen EVOLUTION Cold Air Intake System | Injen Technology

Edge no longer makes the CTS2 Insight Pro that accepts HP Tunes and no longer modifies the CTS2 to the Pro so I'm on the lookout for one. Located in Oshkosh, WI (9one0)four78-eight4zero8

Truck is a 2004 5.9, 50% over, Airdog 4G, 2nd gen manifold ported, Edge Juice w/ Attitude (unlocked 6th tune) and the turbo is a 66/71/13ss with the turbine housing port matched to the manifold. It doesn't start to light until 2000rpm and is slow to build to ~42psi before I run out of rpm's. I...

Looking for a 22-26cm housing. Located in Oshkosh, WI (9onezero)47eight-84zero8

Tranny is from a 1998.5 Dodge Cummins and comes complete with clutch, crossmember, pedals, hydraulics, driveshaft, ect. Essentially everything needed to swap it into anything. Odometer says 334K miles, truck was a delivery truck for a butcher so it should be primarily highway miles. Shifts...

Parting out a 1998.5 Cummins, VP44 powered 24 with all accessories to include starter, harness, turbo, computer, ect-whatever you want. Has 334k on the odometer, no blow-by, looks to have had headwork done (assuming head gasket), new VP44 around 200K miles ago, no leaks, bone stock, and never...

I'm looking for a D61 center section with 3.07 gears or a complete D71 with 3.07 gears. I'm in Oshkosh, WI Text me at (nine one 0) 4seven8-84zero8 or PM me since I'm on here often enough.

Picked it up off of here for my new motor (P-pumped 24V) and ended up selling the truck before putting it on. I paid $300 plus shipping for it and that's what I'd like out of it. I also have a modified front cover I built to allow access to the pump gear without taking everything apart. I'm...

2002 Cummin's 24V VP44 cylinder head-has valves, springs, retainers and the typcial small VP44 cracks between the injectors and valves. Machine shop pressure tested it and said it's fine. But because it's not flawless I can't guarantee anything-$50 2 2" aluminum spacers-8x6.5"-they have 3...

I'm looking at building a front D80 and need a housing for the center section. Just seeing what you guys have out there that's lost a spindle, spun a tube, or destroyed something other than the housing. Last one I bought I paid $100 for the housing with bearing caps and a few inches of tube on...

Probably a long shot but I figured I'd toss it up here as well. I have a 02 Superduty HPD60 complete minus the lockouts that I'm looking to trade for a SRW Chevy front D60, preferably with 4.10's. When I picked the axle up I was told it had 120K on it. Nothing seems worn out or damaged and...

I pulled the back half of my CCSB apart to start a halfassed restoration and when I dropped the fuel tank I noticed I only had 1 fuel line hooked up. This line I know feeds the lift pump, from the lift pump down to a remote fuel filter on the frame, and from there to the IP (dual feed not that...

The slip on my 2 piece rear driveshaft has a bunch of slop and I'm trying to avoid building new driveshafts until the funds come back. My truck is a 98.5 CCSB that was built on a ECLB frame and has a 1480 yoke at the D80. I'll take cut/damaged driveshafts too for just the slip as long as...

Ingersoll Rand air compressor powered by a Honda small engine. It was in the back of my work truck since 2011, has roughly 100 hours on it, pulled it off the work truck last year and has sat since. It was serviced last year when pulled off the truck, a new high idle pressure switch was...

I'm selling the set of these that were just bolted up roughly 30 miles ago. I have the wrong length shock for them and instead of spending another $400 on shocks I'm just going to modify my stock shock mounts. I paid $100 for these less than a month ago, so I'll do $100 shipped to your door...

Well, we're looking to sell the wife's truck and get her something smaller. Nothing wrong with the truck, she's just short and has always driven a mid-sized car her entire life. She just couldn't get used to the size of the truck in traffic. We bought the truck already built and repainted...

I have the tow mirrors off of my 2nd gen CCSB that I don't need anymore. They're power everything and in like new condition. I'm asking $100 obo. you can text me at (91zero)47eight-eight408. Located in Oshkosh, WI

Selling a 6.7 block from a bus that's been dusted. The air filter was never hooked up to the turbo from the factory and driven a few thousand miles. The cylinders will need to be punched out at least 20 over. It's a bare block only as the rotating assembly was reused. Located in Oshkosh, WI...

I converted my truck to SRW and am offloading the DRW axle. It's a D80, 4.10's, uses a 1410 yoke, backlash is within Dana Spicer's spec, last pattern I ran 2 years ago looked great, hub bearings and drum brakes were gone through 40K miles ago and have seen nothing but highway miles and 7 mile...