Search results

Selling my 2004 F-250 SuperCab Lariat 4x4, leather, 6disc cd, power&heated seats 36,500 miles 4.5" Donahoe Racing lift w/ Donahoe Signature Shocks 4" MBRP Cat back with cat and muffler delete pipes New 285/75/16 Nitto TerraGrapplers (less than 3000 miles on them) also have unlimited mileage...

Selling DJ's fuel intensifier with a fuel crossover line for the back of the heads. This kit has never been installed! $375 b/o

Used for only a few weeks. Comes with new adapters for both round and square plugs. $75 plus shipping

Selling off some spare parts from my truck. The Trutrac, Dynatrac cover and DJ's fuel+ have never been installed Detroit Trutrac with new Timkin carrier bearings. Purchased from Randy's R&P $500 b/o plus shipping Dynatrac rear diff cover $150 b/o plus shipping DJ's fuel+ $400...

Hopefully by this time next month I will be in a new truck! I have seen posts talking about Ford's X plan. What exactly is X plan? How does it work? What do I need to bring or tell my dealer? How much money can I save? Where can I get a pin?

I have a FICM to try out and was wondering what's the best way to remove the old one and swap in the new one? Any install tips? What needs to be removed to get at it?

I have a friend with a 2000 Superduty in need of a good, working steering box and also a pair or sway bar end links.

Anyone have the part number for Energy Suspensions trac bar bushings?

Work has a 2004 DMax. Lately the oil pressure at idle is hovering near the red area on the gauge but seems to be fine (about 45 psi) while driving the truck on the road. Is it normal to have the oil pressure drop so low at idle?

1. Accufab intake elbow, satin finish, 05+ style so it eliminates the throttle plate on 03-04 trucks or is a direct bolt on for 05+ trucks $75 2. Airaid intake with filter cleaning kit $175 3. Autometer fuel pressure gauge with ITP adapter line $165 4. Isspro boost, EGT and Transmission temp...

I'm sorry but my MBRP exhaust fits like crap! The round stock MBRP used for the hanger is smaller than what Ford uses, so the entire exhaust floats inside the rubber part of the exhaust hanger. I can grab the exhaust tip and push the entire exhaust about 3" in any direction because the hole in...

Anyone know the oil plug thread pitch on a 2004 Cummins B3.3? We just ordered a Fumoto Valve PN: F104N which has a thread pitch of 18mm X 1.5 but it's too small. Can anyone help?

To make a long story short, my tranny is junk!!! The 04B24 reverse planetary recall that was done on my truck didn't prevent the problem it was supposed to prevent. Actually, it caused my transmission to fail. Anyway the dealer says they are pretty sure the case is no good, so it needs a whole...

My truck is at the dealer due to a delay in the transmission when going from drive to reverse or reverse to drive, and also a little, occasional, shift flare. The dealership just called me and said the problems were caused by the fluid being 2 qts. low. They have no idea where the fluid went...

I have a new Yamaha oil filter for a 660 Grizz sitting in my garage for 2 years. If anyone wants it, its yours

Fault Code Circuit Index Condition Description Probable Causes P0046 VGT Solenoid Turbo/supercharger boost control solenoid circuit range/performance Open circuit, control circuit short to voltage, control circuit short to ground, faulty solenoid, faulty PCM P0069 BARO MAP/BARO correlation...

What are you guys using for transmission pans? If I have to drop the pan to swap out solenoids I may add a new, deeper pan as well.

Like a few others here, I started with some funky shifting this week. Very long delay when going from D-R or R-D. Feels like it engages, then dis-engages, then finally engages with a clunk. I had the same problem last Dec. but after removing my SCT file for a while it went away, now its back! I...

I dont recall reading a single post with 1/4 mile times for the 08's Has anyone run a 6.4 at the track yet??????

Went for my yearly inspection sticker today and was told if I come back next year without new ball joints I will fail. They passed me for this year but I will need to fix them so what do you guys recommend for ball joints? Where are you buying from and how much is it going to cost for parts...