Search results

  1. jambbii

    4.10 Gears AAM 11.5 & 9.25

    4.10s out of my 18 3/4 Ram 30k miles on them and one oil change. Put 5.38s in. $500 or trade for CR/24v performance parts.
  2. jambbii

    Blown Headgasket?

    I just noticed some seeping from the very corner of the driver's side front corner of my cylinder head. I can get it to leak after I beat on it. It doesn't even leak enough to make it down 8 inches from the gasket. It does not pressurize the coolant system. Driving normally or even leaning into...
  3. jambbii

    Piston Suggestions

    Looking for some suggestions for a std bore 12v block. I scored some 24v pistons and when I had the rotating assembly balanced they removed material from the bottom of the piston bowl so I am considering them useless for this application. I am thinking of sticking with stock cummins piston but...
  4. jambbii

    Weird Rail Pressure Issue (altitude or heat related)

    Truck is an 06. Smarty udc, bw363, fass150 and 60%. 130k on the truck. I am stumped guys... This has happened twice while towing. Rail pressure spikes and stays at 26k basically over 1800rpm. It seems like the only actually regulating RP is engine speed. At idle it would go back to normal but...
  5. jambbii

    Pistons

    So I had local machine shop balance my rotating assembly and they ruined my stock 24v pistons. Long story short I need to pick up new pistons. Is there any year that is better than other? Right now, standard bore and JL250hp injectors. Thanks, Josh
  6. jambbii

    S466 Daily Driver

    I have this billet ED s466 .90 ar just sitting in the garage. I was going to use it as a secondary on my 24 P pump mega truck build but I am probably going triples. My daily is my 06 Mega DRW 2wd. I have a built trans with a stock stall converter (Triple disc DPC). Other than an Fass150 and...
  7. jambbii

    95 24 P Pump Build

    Here is my combo so far (crap I have collected over the years) 95 block Balanced rotating assemble 24v pistons (stock) 215 12mm pump benched (no clue on numbers) 250hp JL injectors maxspool 2++ cam ported head with sheet metal intake I forgot what connector tubes I have laying around but I...
  8. jambbii

    2006 Steering Column

    After diagnosing my warped rotors the other day I started tracing a bit of play in the steering. Originally I figured it was the steering shaft or tie rod ends but all of those check out good. Anyone have columns with issues? This is on a 2wd if that matters. Thanks, Josh
  9. jambbii

    24v 2nd gen t4 manifold

    Like the subject says looking for a 2nd gen 24v t4 foot manifold in decent condition. Thanks, Josh
  10. jambbii

    Replacing Injector Nozzles or Whole Injector?

    I have some go fast parts coming in the mail and I have been looking into possibly purchasing 100hp injectors for my 06. The truck has 84K on it right now. Would it be worth it to just replace the whole injector or just the nozzles? I have heard that if you just do the nozzles sometimes they are...
  11. jambbii

    Opies billet intermediate shaft trade/sell

    Going a different rout. Used billet intermediate shaft from Opie. I would actually like to trade for some 24v parts +cash up or down. I am looking for t4 24v manifold, 24v spring/retainers, 24v headstuds or fass/airdog setup for an 06. $600obo Josh
  12. jambbii

    S475 T4 Primary

    I have an ED s475 ( I believe 74/ 83) T4 laying around. I was wondering if it would make good primary over my He351 on my 06. I had done a little searching and I have heard that this is not the best combo. Any thoughts? Josh
  13. jambbii

    Widest DRW Tire (2wd)

    Looking on putting some larger tires on my mega. Has anyone put 275/60/17s on the back? I think they would clear without rubbing. Josh
  14. jambbii

    48re Valve Body

    So I have been out of the diesel game for a little while. The last transmission I built (47rh) the valve body was around $450 if I remember right. I have been looking on messing around with my 06 and I am seeing valve bodies go for $800. Is that just the going rate? My truck probably puts down...
  15. jambbii

    Billet Intermediate Shaft

    Would it be worth putting in a 2wd duallie (500hp)? I have one from Opie laying around and was going to throw it in my 06 when I pull it apart otherwise I might just get rid of it. Josh
  16. jambbii

    1995 single cab body and bed

    Doing a body swap on my 95 single cab (old power wagon). Right now it is pretty complete. I have a clear title to go with the cab as well and interior parts. Bed has a welded in roll pan. Cab with fenders, hood , grill and doors 750. Bed with good tailgate 550. All the pics I have are too big...
  17. jambbii

    1995 Ram single cab project 24v P pump

    I have too many projects, this one is going to be on the backburner for a while if it doesn't sell. Truck is pretty much disassembled right now. I was going to take th body off and brace/clear up the whole chassis. Interior is also taken apart as well. Engine Fresh Hone on short block...
  18. jambbii

    Welding a cylinder head

    I am putting together a 24 P pump engine. I bought a built 24 head from a member here and it has about 30 cracks in it (thanks globaltuck1). Some of them large. I am out of money to dump in this truck now. I do however have a friend that is a very talented tig welder and is willing to help me...
  19. jambbii

    Globaltruck1

    John, I would really appreciate a phone call back. I have left you numerous messages and sent of pm's/emails. There has been very limited comunication ever since I found out that this cylinder head is garbage. Please find 5 minutes out of your day to call me. Thanks, Josh
  20. jambbii

    Just bought an 06, got some questions.

    Just picked up an 06 mega cab 3500 2wd drw with an auto. The truck only has 42k on it now. Has been dealer maintained all of its life and its bone stock. Any comon problems with these trucks? I noticed the rear main seems to be leaking a little bit (nothing hitting the ground). How does the...
Back
Top