Search results

I always wear my seatbelt, but apparently, something broke and the alarm will not shut off. I don't want to pay $80 for a latch assembly hoping the resistors are in it when everyone else seems to be able to jump the wires. I have the mess pictured below in my seatbelt latch. Anyone else? The...

I've looked and can't find any info if you can rebuild a starter on a 6.7L like the older 5.9s. Anyone have any info on where to get the parts, or a good Place to get a reliable one? Thanks!

Bought the truck with this trans in it at 275k. It was bone stock and the dealer I got it from said it had been recently replaced. However, they bought it from an auction so there is no paperwork. I Have a tune on it now. The truck has 305k and will go up as I still drive it. It works perfectly...

I recently bought a 4th gen for my work truck so I could retire the old 2nd gen. I want to build something to take to the drag strip and have some fun. The 2nd gen is an ex cab long bed 4X4. It has 351/475 compounds, maxed 180 pump with 5Ks and a decent motor with 80k on it. I also have a stock...

I have some parts that I won't be needing with my compound setup. S475 turbine housing T4, .90 a/r. It has an HX40 outlet. I like $200 shipped. It is supposed to only have 3 hours run time. I cannot verify that, but it doesn't have any cracks or problems that I could tell. S400 elbow...

Weston's spool valve, T4 flange on both sides, two actuators and some hose, clamps and a T fitting. I bought this from a member on here, ran it for a while and decided to change my turbine housing instead of using it. $590 shipped OBO. S300 T4 68/.91 divided housing, machined for HX40...

A friend near Nashville needs his house boat hauled from Pegram to near Knoxville. He hasn't had any bites on Uship. It is 12' wide by 35' long and weighs 15k. If anyone can help please let me know. Thanks!

For those of you who can't see spending $60+ for an exhaust brake switch and mount, the 1989-02? heater line clamp and a $5 switch from advance auto works well.

I just upgraded to a billet wheel so I no longer need this. It is part number 174267 and has 5-7k run time and I don't see anything visually wrong with it. $20/bo shipped in the lower 48.

I bought the 180HP p-pump he had listed here: http://www.competitiondiesel.com/forums/showthread.php?t=172716 The pump showed up missing some parts (AFC oil fill plug and three bolts). He said he would make it right with me. It's been two weeks and he stopped responding to my text messages...

My turbo is starting to go. I need to get rid of a few things so I can buy a new one. What's a 63/68/14 T4 with an hx40 flange needing a rebuild worth? The comp wheel is barely rubbing the housing. I have a 175HP P-Pump that I ran for a few months. It never had any problems and I took it off in...

Anyone else running one of these pumps? What timing do they like? Any other info on the pump is appreciated. I know it has 12mm plungers and I think 181DVs. I racked the barrels and resealed it. I'm running a 0 plate, 4kgsk, rack plug and tuned AFC. Other mods are in my sig. I'm guessing I'm at...

I'm headed up to Western PA, Northeast PA and out East near Philadelphia. I'll have a partial 8ft bed on the way up and an enclosed 7X14? trailer on the way back. Not exactly sure about the size, but it should be able to carry 3500lbs. I'm planning to leave tomorrow and head back Sunday. Let me...

I'm looking for feedback from people that haul and have set up their brake using a gauge. I have a pacbrake 4" inline brake. I love it so far. Almost instant engagement with the compressor and no tank. I've searched all over and found 13-20psi at idle and 60psi max because of valve springs. I...

I have a good dana 70 out of a truck I bought. Went back with my 80 and locker. What's it worth? I'll start at $800 obo and see what feedback I get. Truck had just under 200k, needs brakes soon, rotors feel smooth and seems like normal backlash. It didn't leak a drop. Located in Nashville, TN. I...

A friend of mine just got his honed block back from the machine shop and I'm not sure if the hone job is done correctly. The shaded areas do not have many cross hatches. It does not feel like they are recessed. A bore gauge would be the best way to determine that, but we don't have one. They are...

I disassembled a motor that developed a knock. One of the pistons was galled and a tappet broke. I can't find much other damage save for light scoring in that cylinder and copper showing on some bearings. It is probably able to be honed. $200 OBO on the block. Buyer arranges shipping. The head...

I need a quote on a few Cummins rebuild kits. Two for sure and one down the line when I tear that motor apart. Right now I'm looking for a 12 valve and a 24 valve rebuild kit. Both trucks are going to be under 500HP daily drivers so no need for forged rods or anything crazy. Looking to...

I have a ton of parts left over from my swap, but I'm not sure what all trucks they fit. Let me know what you are looking for and we can figure it out. All Prices do not include shipping. I have no clue how to price everything so shoot me an offer; worst I can say is no. If you would like a...

I'm looking for the oil pick up tube for an 02 24 Valve. I think one off a 12 Valve will work too. Cummins wants $90 for a new one, but can't get one for a while. Let me know if you have one and what it would cost shipped to 37208. Thanks!