Search results

Has anybody messed around with making there own own tach input that will work with a cts2?? I'm using an edge insight cts2 as a poor mans data logger and would like to be able to data log engine speed with everything else.

Does anybody have any experience in rebuilding these engines. We have rebuilt ours for the third time and we are having issues with the top of the sleeves cracking and breaking off. We did everything by the book used a sleeve press and seemed them at spec, we can't figure out what we are doing...

What is the best Way to get an hx40 down pipe to seal on the turbo flange?

I've been thinking about turning my 96 2500 into a dually and was wondering If I could get away with using the single wheel axle instead of having to buy a dually axle. Any info will be appreciated.

I'm in the market for a billet input shaft and before I buy one I figured I'd see what some peoples opinions are on what shaft I should run. I've seen prices from 560-900 I was looking at suncoast's billet shaft but want some input first.

I have a 96 12 valve with 206,600 miles and a couple weeks ago it started blowing oil from the blowby tube. I took the oil fill cap off and started it to see how much blowby is coming out and there's not a lot, not even enough to move the oil fill cap if you just set the cap on top without...

My dad recently purchased an IH 1468 with the dv550 engine with M&W twin turbo kit on it, he want to do some playing with it and since there weren't many of the tractors made parts are hard to get. Does any body know where we can get pulling parts for the tractor? I know the bottom ends in these...

I have a 98 12 valve auto project truck that I'm turning into a pulling truck, it has full cut DVs, 5x018 modified DAP injectors, no fuel plate, 4K gov springs, 19.5 degrees timing, and Industrial injection s466 workstock/2.5 charger on it. on a free rev around 2,300rpms it misses, if I can get...

I have a 96 12 valve 5spd and all of a sudden it wasn't going to full fuel when I would get one it. I found that the intercooler was rotted out and leaking so I replaced that, but it is still doing it. It doesn't act like it's getting air in the fuel it idles and runs fine and has power on the...

I have a 96 12 valve and the coolant temp would constantly run up to around 210 then drop way down, I put a new thermostat in and it still does it. Someone told me it was normal, I also have a 98 12 valve and it doesn't do the the coolant temp stays steady on it. Any info on why my 96 is doing this?

I replaced both of the front calipers on my 96 because one had a stuck piston on it, also put new pads on too and anti seized the crap out of them making sure I didn't get any on the rotors or pads. All said and done it still pulls the left bad so I figured I still had an air bubble in it, so I...

Just bought a 96 5spd 12 valve and if it's below around 40 degrees if I don't plug the block heater in it seems the batteries get drained but if I plug it in it'll start up no problems. I tested both batteries and both tested good had a new starter put on 2 months ago, I'm clueless I've never...

I am getting a 96 5spd and the owner told me that it had a dual disc south bend but when I test drove it I could tell that it defiantly didn't have a dual disc. Is there any way to tell what clutch it has in it by taking the cover off and looking at it?

Next weekend I'm getting a 96 5spd and the fuel line that is on the overflow valve is leaking bad. I've been trying to find one so can replace it before I drive over 2 1/2 hours home with it leaking fuel, I didn't look at it closely does this line go from the overflow valve to the fuel filter...

I've been looking at turbos and I'd like to hear some opinions on a couple i've been looking at one is fleece's cheetah turbo and the other is industrial injection silver phatshaft 62 which one seems to perform better all around I'm going to put it on a 98 12 valve I do tow a good amount and the...

My oil pressure sensor is bad and I've been trying to find where it is but keep coming up empty handed. I keep reading that it's on the driver side but I can't find it. It's probably behind something and I just haven't got at the right angle to see it..... If anybody could help me out I'd...

I have tons of Chevy 6.5 and 6.2 parts for sale that have been in my road for a while now I want to get everything sold but I'm not going to give it away so please be reasonable. If you are reasonable with me chances are I'll be work with you on price. I would upload pictures but I can't figure...

I'm working on a 500hp build and i'm trying to decide what number of fuel plate to run this truck is my dd so I want to run a plate to keep my fuel economy and egt's down

I'm working on a 500hp build and i'm trying to decide what number of fuel plate to run this truck is my dd so I want to run a plate to keep my fuel economy and egt's down

I'm looking into doing something with my fuel plate but is it worth trying to grind it your self or just buy buy a ground plate? I'm also trying to decide what plate I should run i'm shooting for around 500 to the wheels.