Search results

I will take tha pan off to replace the pan seal, and also install a deep pan. Think a stabel cast pan, have better ability than the sheet metal pan, to seal properly. I have alreade a shift kit, but did you recomend to also replace the accu and servo? Or is this only done if you want very high...

Hello. I shall replace the front cover of the transcase on my 3500, DHD case. Can i remove the t-case without drain the automatic gerarbox? When i search on Ebay for used covers, the most i find is for 1998-2001. Is it not the same case from 1994? What more parts are good the buy at same...

Hello. My fuel shut off solenoid did not work anymore. Have to lift it by hand. Is it worth try repair? How is the Ebay china solenoid? Expensive from Dodge/Cummins dealer? Thanks

Is there any working aftermarket stand alone controller for the HE351ve? That not only rad boost or dp, but also works great on cruising on light load?

Hello. I have a Dodge Ram 1997 12v 3500. I wonder if someone have done a auto to manual swap in these? Which parts needed? Which manual trannys is useable? How much hp and tourqe did these trans hold? //nilsson

Hello. Have a Squeaking and light rattling sound from the serpentine belt. I have replace belt tenisoner (only the wheel), and the belt. Was better one day, and now the same. Have check harmonic balancer but it seems fine, also clean it Only small small movement in and out on idling. Try with...

Hello. Will replace the pan gasket, and rear crank oil seal. Is it big differences in quality, on the brands? The gasket on the transmission pan, is also leaking. But this gasket is only 5 years, but this started to leak after 2-3 years. Some cork gasket. Normal? Which is the best gasket here...

Have anyone try to repair the dually fender? My have some cracks, a small piece on the edge missing. I don't know what kind of plastic it is? Is it possible to repair with polyester and glass fiber? Or is it need to be plastic welded? Maybe some company sell grp copys? //nilsson

Hello. Is it possible to upload movie clip from photobucket or the PC to the forum? Or is it only possible with youtube clip. I will be happy for some advice. Thanks

I have lost the Prop shaft bolts. The bolt from the prop shaft yoke to the flange of the transfer case. Is that some special bolts or only higher grade standard bolts? Have it happen fore someone else, that these came loose during driving, or is it me that are very unlucky? Regards

Hello. Next week i shall try to check the pump timing on a 1995 Passat TDI with 1Z engine. Think i will try with VCDS and saw this nice guide, but i have some questions. ALH engine VW TDI injection pump removal and replacement I see they left the timing at 61 degree at fuel temp 124 degree...

Hello. I shall take the tranny down on my 1997 12v, due to Converter, flexplate and rear crank oil seal replacement. What more uppgrade on the tranny is good to do at same time? I also have a DTT shift kit. I will not do a complete rebuild. I have 024 dv, mack plug, no fuel plate, modify afc...

Hello. Need some parts for my Cummins 12v, 3500 1997. Oil pan gasket. Rear crankshaft oil seal. Serpentine belt To transmission, 47re Deep oil pan Gaskets that can be replace from outside( i only take the gearbox down for a converter change) Some upgraded servo and accumulator. Input shaft...

Hello. Have a Squeaking and light rattling sound from the serpentine belt. I have replace belt tenisoner (only the wheel), and the belt. Was better one day, and now the same. Have check harmonic balancer but it seems fine, also clean it Only small small movement in and out on idling. Try with...

Hello. I shall install an billet converter. Shall i re-use "flexplate to crank" and "flexplate to converter" bolts? Buy new genuine ones, or some aftermarket? Thanks

Have some oil leakage on my 1997 12v, automatic. Both engine ant trans oil. I can se that it leak from the trans oil pan. And maybe a little from the couplings in the front, between the pipe and hose to the oil cooler. The pan gasket has been replaced 3 years ago. Is that i commen problem, or...

Is it common taht the Dash is broken on 2nd gen Cummins? Mine is full of cracks. I think all singel parts in the dash have cracks. The truck is from Florida, is it the sun? Or is it the sun in combinations with cold winters here i Sweden? But i think most crack was befor a took it to Sweden...

Did someone know how much toe-in i shall have, in mm(or inch), if i measure on the rim? 16 inch rim. Thanks.

Did someone know if ther are some document, or "self study programme" on the internet, about the twin turbo tdi? Dont know how many versions it is, but i know its an inline-four in the Amarok, and they olso have a V6? Interested about the turbo setup. Is it parallel, compound or sequential? Or...

Shall fit a Dodge 3500 cummins 1997 12v. //nilsson