Search results

Hi Iam looking to buy a ford ids/vcm package With a laptop Preety much looking for the whole package, Of anyone has one they want To sell let me know, Thanks, Rich3017122565

Hello every one I have a 6.0L with great batteries that will crank all day at 140-180 rpm and will not start. While cranking my Icp is around 900 psi, Ficm lug! Voltage is 46-48V Ipr Duty cycle maxed out at 85%. I have checked all my fuses under the dash and the hood the all seem ok, I have good...

Iam finally deciding to sell my truck i just bought some land and now need a bigger garage and dont have much time for the truck anymore. Iam going to post pics of the truck and what is in it.

Like the title says I have a 03 that will crank but will not start if I pump up the hand pump/ bleed air out the pump will get very hard but will go completely away if i let it sit for 5 minutes and if I go to crank the engine it loses the prime instantly. I have changed the filter, put air in...

Otc genisys scan tool evo 3866 hardly ever Used, brand new condition and works perfectly, OTC genisys updated thru 2009 Asian and Domestic comes with smart cable And all cards, battery charger complete package also has all instructions and hard carrying case. Only selling because I have a Modis...

Iam going to have a twin setup built by Joe @P.D.P the big turbo is going to be a S475 and I am going to either use a htt street stock 62 or a 64/65/14. I was wondering which of the two smaller ones would be the best to go with im thinking the 62 for quicker spool up but would it still hold up...

Like the title says I have a 95 with a 160 pump and when it gets around 190 ect. The truck will stall out or want to stall out it starts fine idles fine at 900 rpm in drive replaced overflow valve, shut off solenoid is adjusted properly it has a FASS 95 gph pump from the tank directly to the...

I need a GTP38R garrett ball bearing compressor housing for a 7.3L my wheel has rubbed mine, i got a wheel now i just need a housing if anyone has one or knows where to get one please let me know. Thanks, Rich 301-712-2565

My neighbor who is a good friend of mine has a 06. so far hes told me it has a fass 95gph pump, 120 hp injectors, smarty programmer, and a super b turbo. any way he told me to look at it for him , when driving at any speed whenever you hit right around 30 psi boost the truck seems to be de...

Hi im helping my cousin with his truck its is a 00 7.3L at idle it sounds fine starts great, all normal but driving slowly it starts missing/ lopeing and when you put the pedal on the floor it runs great no missing,no codes and icp psi seems good does this sound like a Cmp or tps Problem to...

this past september i posted mods of my 5speed 96 service truck and was asking you all for some advice on what was next well so far so good i want to get the most MPG i can and most power i can but more tword mpg side this is what i have so far i need some help to see what i should do for better...

they are from Industrial Injection iam not sure what the lift or BAR PSI is i drove up my rroad twice less then 1 hour of 5 miles on them, but They are to big for my setup. but maybe one of you guys could use them or maybe want to swap for some 5x .022's or 5x .018's $950.00 :ft:

Like the title says i have a loaded down 96 12 valve service truck with a South bend DD and 3.54 gear ratio, and i was wondering what everybody thought about what to do next, so far i have a 215 pump with 0 plate ,3000 rpm springs, 191 DV's, gov spring in afc, star wheel up, timing is at 16...

Like the title says i have a loaded down 96 12 valve service truck with a South bend DD and 3.54 gear ratio, and i was wondering what everybody thought about what to do next, so far i have a 215 pump with 0 plate ,3000 rpm springs, 191 DV's, gov spring in afc, star wheel up, timing is at 16...

i have studs but no torque specs, anyone know what the torque steps/ retorque for 12valve are?

A guy brought me over his truck for a rapping noise turned out the dealership put 4 injectors in the truck earlier and never readjusted the valves some were loose some very tight. I adjusted the valves and runs fine, but he says every now and then when its cold it the truck sputters and sounds...

got the electric water pump on and i was wondering if anyone had a tensioner pulley they wanted to sell, so i dont have to run the ribbed side of the belt on a smooth pulley.

http://www.scheiddiesel.com/display_part/2504.php Has anybody used this yet what is the advantage of geting rid of afc and boost lines? to adjust you still have to pull cover so there must be another reason. :thankyou2: Rich

a friend of mine dropped off a truck for me to look at and so far i think i am looking at more than one problem. first of all there is excessive pressure going into the coolant system maybe some oil as well, and coolant in exhaust but no coolant or fuel in oil, iam not to sure if thats going to...

1 Fass 150 gph pump only unit with harness and hose $300.00 1 set of 6" mitre cut stacks 36" long noStacks only no t pipe $250.00 2 sets of stock 12v injector lines $50 a peice 2 stock head gaskets 12 v $40 a peice 1 spearco intercooler with chrome pipes and boots $1,000 1BD pressure...