Search results

Has anyone had problems with the oil pump failing?

2006 Dodge QCSB 3500 SRW 4x4 SLT w/ 42,XXX miles • S300 64mm rebuilt by Mumua Diesel (9/2011) • ATS manifold – ported • 5” turbo back exhaust – Magnaflow Stainless • K&N intake with Amsoil Dry Filter • Air Dog II 165 • Smarty S-06 w/ TNT-R (4000 RPM Rev Limit) • EEP Coolant By-Pass Kit w/...

As the title states, I am looking for a CP3 in the Western PA/ Eastern OH area. I would prefer to buy one from someone locally. Let me know, what you have. Thanks

What size are the fittings going into the heat exchanger? Can the large fittings in the exchanger be removed? Thanks!

Do you still sell the turbo smart system? If so, how much? Thanks!

I've been looking at these systems to protect my turbo at the end of a run. Does anyone have any experience with either one? I did find 1 thread about the turbo smart, but nothing on the BD system. Thanks!

I have a set of Trxus STS 33 x 12.5 x 17 I am looking to sell. $600 pick up only.

For sale is the stock turbo off of my 06. It had about 38,000 miles on it, when I pulled it off. It has no in and out play, and little bit of play side to side. $300 shipped.

Is there anyone in Western PA with Starscan? I live in the Slippery Rock Area, and work in Harmarville area. My truck is throwing 2 codes: P0148 (HPCR-high pressure common rail) and P0191 (Fuel pressure sensor performance). I scheduled an appointment at my local dealer for a scan, but I would...

Fueling Problems? How do I know if I have a bad FCA on a twin pump truck? Tuesday night and last night at my local pull, my truck would not fuel on the line. I was trying to build boost, but it won't build up, it just rolls coal and won't light the charger. We thought the lift pump was...

I know I've seen it, but I cannot find it. I'm looking for the wiring diagram that shows how to keep the ECM from locking the torque converter. I have the T/C lock up switch installed, and working on the street at low speed. However, when I am sledpulling, I don't believe the ECM is allowing...

As the title states, I'm looking for a rail pressure gauge with recall capability. Quadzilla no longer makes one for the 5.9, anyone have any suggestions? Does anyone know if the EFI Live for Cummins will be able to read rail pressure from the OBD II connector?

I installed an II 64 Silver bullet, and I keep getting an over boost code. I am running a Smarty and I have the wastegate turned off. Do I need a boost fooler?

Does any one have any good pics for U-joint shield mounting on a 3rd gen? I would prefer not to weld. I searched the thread, and found some pics, but was wondering if anyone had any better ideas. Thanks!

A friend of mine has Flux 3's with very low miles, maybe 2000-3000 miles on the tips over the last 2 years. They were used for sled pulling, I'll say maybe 15 hooks on them. They started out as Flux 2.5's, and were opened up to the 3's. He's looking to got to 4's, and I want 3's. What are the...

A friend of mine has Flux 3's with very low miles, maybe 2000-3000 miles on the tips over the last 2 years. They were used for sled pulling, I'll say maybe 15 hooks on them. They started out as Flux 2.5's, and were opened up to the 3's. He's looking to got to 4's, and I want 3's. What are the...

What size wrench/tool is needed hold the injector body to remove the nozzles? I'm planning on making my own, or grinding down the appropriate size wrench.

I'm looking for a quote for a packed deal for a set of Di-Procol Gauges for a 2006 Dodge. I would like the color matched a pillar mount, with EGT, Boost 60lb, and Trans temp (full sweep). White Face, Black Bezel, Red Pointer. I'm looking for a quote because I've heard its been difficult to...

I just had my trans built and as part of the install we added the TC lock up switch. The #7 wire (yellow w/ light blue) wire was tapped, and run to a 20A switch with a 33ohm resistor in between, and the other side was run to ground. With the truck in drive and the switch off I measure 14.5...

Is NADM going to have a pull at Stoneboro this year?