Search results

Just finished an auto swap in 94 2500 and have a transgo manual vb kit in a stock valve body. As of right now we have two switches to control solenoids and three wires coming out of plug. 12v sourced from ignition. L/u and O/d circuits run from trans to switch and then ground. Anyone have any...

About finished up with 05 Hemi ppump 24 conversion. Trying to figure out the water temp and oil pressure and how to get it to work on the dash. From what I have gathered the Hemi PCM uses many inputs and the gauges are dummy gauges. Anyone that has done the swap have any insight on getting...

What are you guys using for labor guides for performance shops? Obviously some things probably aren't going to be in there but is there a diesel specific labor guide out there?

For you guys running performance shops what are you using for scan tools? I have EFI already but looking for something to do cut out tests balance rates etc. I have read quite a bit of you saying the auto enginuity is the way to go. This will be used on strictly the big three diesels. I...

Ok guys just got the motor out of the 06 soon to be shop race truck. First off truck is 06 cummins Plans so far: Single fleece s480 steed speed competition t4 gated mani sending the head to Mtn High to have them do bigger valves, machine intake off for hellman side draft and port job 250%...

Working on a buddies 03 and the truck has no low end power Put a s06 tune on it TNT sw7 and not much difference from stock and have since then installed a bully dog tune with the watchdog until he can afford the smarty Anyway driving it is weird it takes forever to build boost but once you hit...

Anyone tried or been able to replace front band with just a valve body and pan removal? Leaving the Trans in truck?

04.5 Suncoast full billet 47re manual vb 120k Pulled head because of misfire saw some scoring on number 3 possible broken ring Would like to sell complete or motor and Trans Make offer

The 5.9 in my 04.5 is coming apart because of blowby and a miss at idle. #2 and #6 have some scoring on the walls which I'm guessing are a couple broken rings. I've read about some guys swapping in a 6.7 and running the 5.9 ECM with 03 style nozzles. I can either rebuild my 04 with qsb pistons...

1999 kt 4 mil banshee Welded trued crank dune port Paul turner powerhead Sudco flat slide carbs T-5s Chrome everything Cascade engine covers +6 extended swing arm Airbrushed plastics w/ matching seat cover Renthal bars Barnett clutch Paddles and Mohawks Extremely good condition runs awesome...

suncoast Billet input shaft and drum $600 has maybe 1000 miles on it nothing wrong with it had this as a spare

I just recently got a gt4094 ball bearing charger that the turbine housing has had the wastegate ports blocked off and welded. I plan on running this as a single to start but my question is should I run an external gate with this housing or buy a different housing and run the internal wastegate...

Any body know the difference in the automatic length compared to the standard and how much to take out of the front drive shaft. I measured the length about 7 months ago and forgot. i seem to recall it being 5 inches but not sure. My trans is out and I am trying to get everything together to run...

I picked up cat turbo today havent got to measure it my calipers are at work. Any one know the specs on a cat p/n tc7685 s/n c4ds010h0288a 084? I am curious to know if this is anything worth using because i got it for free and there is no shaft play but I havent got to measure it yet. thanks

Are their race valve bodies Full manual? I tried to call tonight but they were gone already. Also do they allow first gear lockup?

I have been doing some reading on the supercharger and turbo setups and from what i have gathered you can either run the procharger as the atmospheric turbo or run a roots style as the secondary because of the internal bypass. I have read that prochargers dont like much boost or heat through...

I ended up losing reverse in my manual vb 47re that I swapped for the 5600 awhile back. My reverse band and drum are shot. My rear sprag started to spin in the case also. My reverse band piston spring retainer is bent in an odd way also. This trans was originally was in a pulling truck, It has...

Bought Suncoast trans with this valve body and swapped with a manual valve body to run in my 3rd gen. Worked great before swap. All electronics included Asking 375 shipped 970-420-2233

I have a suncoast triple disk and I am pretty sure I fried the lock up clutch in the converter. Is it possible to go through a converter and fix whats needed or do I have to buy new. I am very new to the automatic world. thanks

Anyone have experience with proxes in the snow really want to get proxes on my truck but living in Colorado brings quite a bit of snow on the roads. If I have to I will buy two sets of tires but that will get old changing every season. Any one drive proxes in the snow? Howd they do?