Search results

Looking for a stock downpipe, mostly complete as I know some have to be cut off the exhaust. Preferably in the GA area.

All of these came off my '01 24 valve *Will have pics up this weekend* BD Super B Special Downpipe, clamps and any hardware that came with it. About 6k miles on it, too laggy with an untapped quadzilla. $1200 OBO S&B Intake Filter needs to be cleaned and re-oiled. All hardware with it...

With the truck warmed up, the idle is around 750 in neutral with the A/C on, 800 with it off. If I try to adjust it by my chilton's manual to 850 with the A/C on, it jumps to 1100 RPMs when I turn it off (the A/C). It seems to be either at 750 with the A/C on and 800 with it off, or 850 on...

So a while back, I picked up a 2wd nv4500 for my '98 for a really good price. I was going to swap the rear housing on the back for the 4wd version and the mainshaft, but I got another good deal on a driver's side drop divorce-mount np205 out of a mid-70's ford. I tore it down, ordered a...

Stock '01 automatic. 160k miles or so. Today, out of the blue, the truck had zero oil pressure. I parked it at the house, the pressure was fine. 3 hours later, I had none. When I stop suddenly, it will jump just above the red line, then drop back down. Plenty of oil, although it needs to...

Truck has been doing it ever since I started messing with it about 2 years ago. Started with a 3K GSK, went to 4K's, back to 3K's and finally back to 4K's with the 5-speed swap. The issue is whenever the truck's RPMs are raised above idle, then truck returns to idle, then goes slightly below...

I believe they came on the cab and chassis 2nd gens. Haven't had any luck finding one, so if you know where one is for sale, let me know. As long as it's in good shape and not bent up or anything. Thanks.

Went from running one of Smokem's GSK setups for about 6 months to a 3k GSK tonight, but I can't remember which way to turn the adjuster. After installation, it idled at about 600 RPMs. Turned the idle up to about 850, but now if I rev it up in neutral, it will stay at 1500 RPMs. I have to...

With just a #0 plate and a set of GSKs, what would be a good single to keep the temps below the 1300-1400* range? Truck has good power for me now, and I don't forsee any future upgrades to it, except maybe 2-3* more timing (stock now). On long pulls, the temp gets up to around 1500 with no...

Okay, in my dealings with my TV cable, I found the transmission mount is broke. The bolts are in the bottom, and the mount itself is good, but the transmission is not secured to it, if that makes sense. I can move the transmission a good inch side-to-side. The driver's side engine mount is...

Had it for about a year, but only ran it a couple of months. Comes with just the plate, no boost elbow or breakoff screw. Asking $50 shipped in the continental 48. Or if you're close by and want it, I'm in Ogden, UT.

'98 3500 12 valve, 215 pump auto 4x4. The truck, in "D", shifts from 1st to 3rd at 5 mph. I have a TC lockup switch on it, so it basically hits 3rd and locks AT 5 MPH!!! It's been like this ever since I bought it. What could be causing it? The TPS didn't seem like it fit the bill. Anyone...

I have a 50 gallon aux tank (not sure on the manufacturer) with a fill rite 15 GPM pump. Good shape, has the normal wear/scratches from being in the bed. Pump was used about 10 times, practically brand new. Tank does not leak, or have any cracks/holes in it. Asking $350 for everything. Also...

I don't have any room at our new house in Utah, so this one has to go. Truck is located in Lizella, Georgia. I think it has 150,XXX (estimated mileage, but should be pretty close, within 3,000 miles) on it. I haven't seen the truck in 4 months, as it's at a friend's farm. Really good shape...

Bought back in April from another board member. Never installed them, plans changed to a flatbed. Located in Ogden, UT and asking $50 plus shipping. When these were shipped from WI to GA, it was $10.

I noticed my solenoid does not "click" or stay in the up position with the key on. It will come up some, but not stick in the up or "run" position. It starts and runs fine, at least I think. Can the shutoff lever, inbetween the run and stop position, cause a power loss? If I lift it up...

Truck is a '98 automatic, but it's got a CPL of 2175/pump number 913. I need to know, if possible, what year the engine is. I can get any numbers someone would need. I ordered the upper radiator hose for a '98, but the hose was too short. I noticed on autozone's website that there are...

What are the case differences between them? Guy locally has one of each for sale, but the cases are broke. Wondering if I can put the HD stuff in my LD, and if not, what the differences are.

All parts were bought from a truck shop. 5" flat-top, even with the cab. Comes with all parts except the clamps to mount them to the front of the bed, a 10" piece of 5" pipe to make the stacks go all the way to the edges of the bed and flex pipe. The reducer is kind of banged up on the 4"...

Got a set of 370s for sale. Asking 270 plus shipping. Will come with washers for the injectors/lines. About 3k on them. Ran great, just too hot for my stockish setup. Also have a #0 plate I cut about 4 days ago, and a stock plate out of a 180 pump, I believe. Asking $25 plus shipping each...