Search results

Just swapped my 5r for a BTS 4R100. I swapped in a new 4r100 pcs harness and it now includes a usb cable. I finished all my wiring and plugged it up to check everything out and it says It needs a driver. I dont have a clue what driver it needs, and of course Its after 5 anyplace in the US and no...

Pump was originally bought through East Coast Diesel. Pump ran well but the engine spun a bearing. The pump was only pulled 6 times, no road miles. I'm parting the performance parts off this engine and putting it back closer to stock. I have it listed on ebay as well. $1500 and I'll pay the...

Looking for the underhood wiring from a 98 12v. This is the wiring from the large plug under the dash, fuse block, ect.

Looking for brake hardware for a 94 dana 80. i have all the springs and new shoes, but am in need of the ebrake lever and the bar that goes between the shoes on the left and right. Ideally Id buy the whole assembly backing plate and all. These parts are no longer available at dodge, so Im at the...

Rodeheaver's Speed Shop western PA's #1 speed shop Heard from a friend that they were dynoing this sat 4-21. We called and they said 9am to whenever, gas or diesel, all are welcome. The only thing they ask of the diesel owners with stacks is bring your own pipe for the stacks, smoke tube, or...

Looking for the part of the tps bracketry that connects the tps to the fuel pump lever on a 93 VE pump. It is NS1 at Dodge and so far I've had no luck tracking it down. you can hit me up here, email nathan@seriousdiesel.com or call 304-864-4600 and ask for Nathan.

Thanks yet again for the quick parts and info for dads 8.3. It dropped a valve seat on monday and we had all the parts here and had it back together wed by midnight. Really appreciate it!!:rockwoot:

I have a 2001 Chevy Duramax at my shop. Initially It came in with no rail pressure. I installed a new modded pump from II, and a new rail psi sensor. Truck now has rail pressure, rpms show up on the scan tool, good lift pump pressure from the lift pump. Occasionally the truck will start and run...

Does anyone know if the larger industrial oil pan will fit in the 94-98 trucks with the sump to the rear without modifying the crossmember?

I have a few sets of Total Seal gapless rings being made for the second ring right now for 12v mahle pistons but was just curious if anyone had been using any other aftermarket rings for higher horsepower engines spinning higher (5500 and up) RPM.

Swapped a 97 12v into a 06 Ford this winter that was a v10. I used the factory v 10 radiator, 12 fan and clutch. I also installed a real coolant temp guage since the v10 factory guage is head temp not coolant temp. Problem Im having Is that the fan is kicking on too early. Temp consistantly runs...

Anyone experienced a broken rocker shaft on a stock truck? I just fixed this truck a few weeks ago for a customer from an over rev courtesy of a healthy shot of ether. I put in new pushrods, and tore down the front cover, replaced the cam and crank pins, put new buttons on the valve bridges, and...

Had a guy bring me a performance box to ask if I knew anything about it. He got the thing in a trade of some sorts. This thing looks pretty dated, and he said he knew it did tap the pump wire. Do any of you original diesel performance gurus recognize this box? Anyone have any info on it?:thankyou2:

anyone use a timer or the ford pcm to run the grid heaters on there conversions? Im doing 2 right now that need to be automatic on timers, Not push buttons, or what not. Anybody have their truck fixed up to run the grid heaters like this?

Anyone drive on the street in 4wd with a limited slip in the front of a 2nd gen Dodge? I was going to put one in my truck because I hope to do a little sled pulling this summer and figured it would be the simplest and cheapest route to get all 4 wheels turning and still be able to drive in the...

Im converting a 2000 excursion from a 7.3 to a 12v. since the excursion has hydroboost i dont need a vaccum pump. is there a way to install a power steering pump without having the vac pump that was origionally on a 12v from a dodge?

i have an 06 king ranch im getting ready to put a 12v in. Is there any real gain to switching the vaccum assist brakes out for hydroboost? is braking better? Im using a 12v and it has a Vaccum pump so thats not an issue.

Just got an awesome deal on a 06 F-250 V-10 King Ranch with a blown up engine. My understanding is that this truck has the 5R110. How well do the 5R110 transmissions hold up? Any major problems, parts or pieces that need upgraded, Will they hold a 5-600 hp Cummins? This truck will be a daily...

Anyone know the best way to get the crankshaft gear off with the engine still in the truck? I have a truck with some bent up pushrods and would like to inspect the pin before I put it all back together.

Anyone going to PRP Saturday? what time does it start? I was considering coming but the website doesn't have much info.